Thu Jun 13 20:29:06 CEST 2002 ide-clean-90
- Implement the assertion that the lock is already held, if we run
ata_status_poll.
- The usual host chip code load from Bartomiej onierkiewicz. Fortunately
I'm able to check the sis5513 fixes on a life system.
More serious stuff... for IDE 88:
- implement ata_best_pio_mode() in ata-timing.c
(play safer than driver's config_chipset_for_pio())
- replace config_chipset_for_pio() by ata_best_pio_mode()
in host chips drivers
(trivial for hpt34x.c, hpt366.c and serverworks.c,
non-trivial for cmd64x.c and sis5513.c)
- set PIO also for (U)DMA modes in cmd64x_tune_chipset()
(cmd64x.c)
- fix bug in setting PIO0-2 for devices also supporting PIO3/4
(sis5513.c)
- misc cleanups
- Rename XXX_do_request back do do_request. This was just tmporary tagging.
- Move ata_taskfile() call down to the ide-disk request handler.c, which is the
only place needing it. Rename ata_taskfile to ata_do_taskfile(). This
allowed us to implement the assertion that ata_do_taskfile() will be only
called with the channel lock already held.
diff -urN linux-2.5.21/drivers/ide/alim15x3.c linux/drivers/ide/alim15x3.c
--- linux-2.5.21/drivers/ide/alim15x3.c 2002-06-09 07:30:37.000000000 +0200
+++ linux/drivers/ide/alim15x3.c 2002-06-13 22:53:06.000000000 +0200
@@ -176,11 +176,6 @@
return ide_config_drive_speed(drive, speed);
}
-static void config_chipset_for_pio(struct ata_device *drive)
-{
- ali15x3_tune_drive(drive, 5);
-}
-
#ifdef CONFIG_BLK_DEV_IDEDMA
static int config_chipset_for_dma(struct ata_device *drive, u8 udma)
{
@@ -253,7 +248,7 @@
on = 0;
verbose = 0;
no_dma_set:
- config_chipset_for_pio(drive);
+ ali15x3_tune_drive(drive, 255);
}
udma_enable(drive, on, verbose);
diff -urN linux-2.5.21/drivers/ide/ata-timing.c linux/drivers/ide/ata-timing.c
--- linux-2.5.21/drivers/ide/ata-timing.c 2002-06-09 17:44:23.000000000 +0200
+++ linux/drivers/ide/ata-timing.c 2002-06-13 22:53:06.000000000 +0200
@@ -270,3 +270,25 @@
return 0;
}
+
+u8 ata_best_pio_mode(struct ata_device *drive)
+{
+ static u16 eide_pio_timing[6] = { 600, 383, 240, 180, 120, 90 };
+ u16 pio_min;
+ u8 pio;
+
+ pio = ata_timing_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
+
+ /* downgrade mode if necessary */
+ pio_min = (pio > 2) ? drive->id->eide_pio_iordy : drive->id->eide_pio;
+
+ if (pio_min)
+ while (pio && pio_min > eide_pio_timing[pio])
+ pio--;
+
+ if (!pio && drive->id->tPIO)
+ return XFER_PIO_SLOW;
+
+ /* don't allow XFER_PIO_5 for now */
+ return XFER_PIO_0 + min_t(u8, pio, 4);
+}
diff -urN linux-2.5.21/drivers/ide/ata-timing.h linux/drivers/ide/ata-timing.h
--- linux-2.5.21/drivers/ide/ata-timing.h 2002-06-09 17:44:23.000000000 +0200
+++ linux/drivers/ide/ata-timing.h 2002-06-13 22:53:06.000000000 +0200
@@ -83,5 +83,6 @@
extern struct ata_timing* ata_timing_data(short speed);
extern int ata_timing_compute(struct ata_device *drive,
short speed, struct ata_timing *t, int T, int UT);
+extern u8 ata_best_pio_mode(struct ata_device *drive);
#endif
diff -urN linux-2.5.21/drivers/ide/cmd64x.c linux/drivers/ide/cmd64x.c
--- linux-2.5.21/drivers/ide/cmd64x.c 2002-06-13 20:15:09.000000000 +0200
+++ linux/drivers/ide/cmd64x.c 2002-06-13 22:53:06.000000000 +0200
@@ -152,16 +152,14 @@
}
/*
- * Attempts to set the interface PIO mode.
- * The preferred method of selecting PIO modes (e.g. mode 4) is
- * "echo 'piomode:4' > /proc/ide/hdx/settings". Special cases are
+ * Attempts to set the interface PIO mode. Special cases are
* 8: prefetch off, 9: prefetch on, 255: auto-select best mode.
* Called with 255 at boot time.
*/
static void cmd64x_tuneproc(struct ata_device *drive, byte mode_wanted)
{
int recovery_time, clock_time;
- byte recovery_count2, cycle_count;
+ u8 recovery_count2, cycle_count, speed;
int setup_count, active_count, recovery_count;
struct ata_timing *t;
@@ -172,10 +170,14 @@
/*set_prefetch_mode(index, mode_wanted);*/
cmdprintk("%s: %sabled cmd640 prefetch\n", drive->name, mode_wanted ? "en" : "dis");
return;
- case 255: mode_wanted = ata_timing_mode(drive, XFER_PIO | XFER_EPIO);
}
- t = ata_timing_data(XFER_PIO_0 + min_t(byte, mode_wanted, 4));
+ if (mode_wanted == 255)
+ speed = ata_best_pio_mode(drive);
+ else
+ speed = XFER_PIO_0 + min_t(u8, mode_wanted, 4);
+
+ t = ata_timing_data(speed);
/*
* I copied all this complicated stuff from cmd640.c and made a few minor changes.
@@ -213,6 +215,9 @@
cmdprintk("%s: selected cmd646 PIO mode%d : %d (%dns), clocks=%d/%d/%d\n",
drive->name, t.mode - XFER_PIO_0, mode_wanted, cycle_time,
setup_count, active_count, recovery_count);
+
+ drive->current_speed = speed;
+ ide_config_drive_speed(drive, speed);
}
static int cmd64x_ratemask(struct ata_device *drive)
@@ -283,13 +288,26 @@
}
}
-static void cmd680_tuneproc(struct ata_device *drive, u8 mode_wanted)
+static void cmd680_tuneproc(struct ata_device *drive, u8 pio)
{
- struct ata_channel *hwif = drive->channel;
- struct pci_dev *dev = hwif->pci_dev;
- u8 drive_pci;
+ struct ata_channel *ch = drive->channel;
+ struct pci_dev *dev = ch->pci_dev;
+ u8 unit = (drive->select.b.unit & 0x01);
+ u8 addr_mask = (ch->unit) ? 0x84 : 0x80;
+ u8 drive_pci, mode_pci, speed;
+ u8 channel_timings = cmd680_taskfile_timing(ch);
u16 speedt;
+ pci_read_config_byte(dev, addr_mask, &mode_pci);
+ mode_pci &= ~(unit ? 0x30 : 0x03);
+
+ if (pio == 255)
+ pio = ata_best_pio_mode(drive) - XFER_PIO_0;
+
+ /* WARNING PIO timing mess is going to happen b/w devices, argh */
+ if ((channel_timings != pio) && (pio > channel_timings))
+ pio = channel_timings;
+
switch (drive->dn) {
case 0: drive_pci = 0xA4; break;
case 1: drive_pci = 0xA6; break;
@@ -302,7 +320,7 @@
/* cheat for now and use the docs */
// switch(cmd680_taskfile_timing(hwif)) {
- switch(mode_wanted) {
+ switch(pio) {
case 4: speedt = 0x10c1; break;
case 3: speedt = 0x10C3; break;
case 2: speedt = 0x1104; break;
@@ -311,50 +329,11 @@
default: speedt = 0x328A; break;
}
pci_write_config_word(dev, drive_pci, speedt);
-}
-
-static void config_cmd64x_chipset_for_pio(struct ata_device *drive, u8 set_speed)
-{
- u8 set_pio = ata_timing_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
-
- cmd64x_tuneproc(drive, set_pio);
- if (set_speed)
- (void) ide_config_drive_speed(drive, XFER_PIO_0 + set_pio);
-}
-
-static void config_cmd680_chipset_for_pio(struct ata_device *drive, u8 set_speed)
-{
- struct ata_channel *hwif = drive->channel;
- struct pci_dev *dev = hwif->pci_dev;
- u8 unit = (drive->select.b.unit & 0x01);
- u8 addr_mask = (hwif->unit) ? 0x84 : 0x80;
- u8 speed;
- u8 mode_pci;
- u8 channel_timings = cmd680_taskfile_timing(hwif);
- u8 set_pio = ata_timing_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
-
- pci_read_config_byte(dev, addr_mask, &mode_pci);
- mode_pci &= ~((unit) ? 0x30 : 0x03);
- /* WARNING PIO timing mess is going to happen b/w devices, argh */
- if ((channel_timings != set_pio) && (set_pio > channel_timings))
- set_pio = channel_timings;
+ speed = XFER_PIO_0 + min_t(u8, pio, 4);
- cmd680_tuneproc(drive, set_pio);
- speed = XFER_PIO_0 + set_pio;
- if (set_speed) {
- (void) ide_config_drive_speed(drive, speed);
- drive->current_speed = speed;
- }
-}
-
-static void config_chipset_for_pio(struct ata_device *drive, byte set_speed)
-{
- if (drive->channel->pci_dev->device == PCI_DEVICE_ID_CMD_680) {
- config_cmd680_chipset_for_pio(drive, set_speed);
- } else {
- config_cmd64x_chipset_for_pio(drive, set_speed);
- }
+ drive->current_speed = speed;
+ ide_config_drive_speed(drive, speed);
}
static int cmd64x_tune_chipset(struct ata_device *drive, byte speed)
@@ -403,11 +382,13 @@
case XFER_PIO_1:
case XFER_PIO_0:
cmd64x_tuneproc(drive, speed - XFER_PIO_0);
- break;
+ /* FIXME: error checking --bkz */
+ return 0;
default:
return 1;
}
+ cmd64x_tuneproc(drive, 255);
#ifdef CONFIG_BLK_DEV_IDEDMA
(void) pci_write_config_byte(dev, pciU, regU);
#endif /* CONFIG_BLK_DEV_IDEDMA */
@@ -510,14 +491,13 @@
case XFER_PIO_1:
case XFER_PIO_0:
cmd680_tuneproc(drive, speed - XFER_PIO_0);
- break;
+ /* FIXME: error checking --bkz */
+ return 0;
default:
return 1;
}
- if (speed >= XFER_MW_DMA_0)
- config_cmd680_chipset_for_pio(drive, 0);
-
+ cmd680_tuneproc(drive, 255);
if (speed >= XFER_UDMA_0)
mode_pci |= ((unit) ? 0x30 : 0x03);
else if (speed >= XFER_MW_DMA_0)
@@ -552,12 +532,6 @@
mode = ata_timing_mode(drive, map);
- if (mode < XFER_SW_DMA_0) {
- config_chipset_for_pio(drive, 1);
- return 0;
- }
-
- config_chipset_for_pio(drive, 0);
return !drive->channel->speedproc(drive, mode);
}
@@ -568,6 +542,8 @@
int on = 1;
int verbose = 1;
+ hwif->tuneproc(drive, 255);
+
if ((id != NULL) && ((id->capability & 1) != 0) &&
hwif->autodma && (drive->type == ATA_DISK)) {
/* Consult the list of known "bad" drives */
@@ -610,7 +586,7 @@
on = 0;
verbose = 0;
no_dma_set:
- config_chipset_for_pio(drive, 1);
+ hwif->tuneproc(drive, 255);
}
udma_enable(drive, on, verbose);
diff -urN linux-2.5.21/drivers/ide/device.c linux/drivers/ide/device.c
--- linux-2.5.21/drivers/ide/device.c 2002-06-11 00:17:34.000000000 +0200
+++ linux/drivers/ide/device.c 2002-06-14 00:02:43.000000000 +0200
@@ -126,9 +126,8 @@
* setting a timer to wake up at half second intervals thereafter, until
* timeout is achieved, before timing out.
*
- * FIXME: Channel lock should be held.
+ * Channel lock should be held.
*/
-
int ata_status_poll(struct ata_device *drive, u8 good, u8 bad,
unsigned long timeout,
struct request *rq, ide_startstop_t *startstop)
@@ -159,6 +158,7 @@
if (ata_status(drive, good, bad))
return 0;
}
+
*startstop = ata_error(drive, rq, "status error");
return 1;
diff -urN linux-2.5.21/drivers/ide/hpt34x.c linux/drivers/ide/hpt34x.c
--- linux-2.5.21/drivers/ide/hpt34x.c 2002-06-13 20:15:09.000000000 +0200
+++ linux/drivers/ide/hpt34x.c 2002-06-13 22:53:06.000000000 +0200
@@ -67,43 +67,6 @@
return ide_config_drive_speed(drive, speed);
}
-static void config_chipset_for_pio(struct ata_device *drive)
-{
- unsigned short eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
- unsigned short xfer_pio = drive->id->eide_pio_modes;
-
- u8 timing, speed, pio;
-
- pio = ata_timing_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
-
- if (xfer_pio > 4)
- xfer_pio = 0;
-
- if (drive->id->eide_pio_iordy > 0) {
- for (xfer_pio = 5;
- xfer_pio>0 &&
- drive->id->eide_pio_iordy>eide_pio_timing[xfer_pio];
- xfer_pio--);
- } else {
- xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
- (drive->id->eide_pio_modes & 2) ? 0x04 :
- (drive->id->eide_pio_modes & 1) ? 0x03 : xfer_pio;
- }
-
- timing = (xfer_pio >= pio) ? xfer_pio : pio;
-
- switch(timing) {
- case 4: speed = XFER_PIO_4;break;
- case 3: speed = XFER_PIO_3;break;
- case 2: speed = XFER_PIO_2;break;
- case 1: speed = XFER_PIO_1;break;
- default:
- speed = (!drive->id->tPIO) ? XFER_PIO_0 : XFER_PIO_SLOW;
- break;
- }
- (void) hpt34x_tune_chipset(drive, speed);
-}
-
static void hpt34x_tune_drive(struct ata_device *drive, u8 pio)
{
(void) hpt34x_tune_chipset(drive, XFER_PIO_0 + min_t(u8, pio, 4));
@@ -177,7 +140,7 @@
on = 0;
verbose = 0;
no_dma_set:
- config_chipset_for_pio(drive);
+ hpt34x_tune_chipset(drive, ata_best_pio_mode(drive));
}
#ifndef CONFIG_HPT34X_AUTODMA
diff -urN linux-2.5.21/drivers/ide/hpt366.c linux/drivers/ide/hpt366.c
--- linux-2.5.21/drivers/ide/hpt366.c 2002-06-13 20:15:09.000000000 +0200
+++ linux/drivers/ide/hpt366.c 2002-06-13 22:53:06.000000000 +0200
@@ -682,44 +682,6 @@
return ide_config_drive_speed(drive, speed);
}
-static void config_chipset_for_pio(struct ata_device *drive)
-{
- static unsigned short eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
- unsigned short xfer_pio = drive->id->eide_pio_modes;
- u8 timing, speed, pio;
-
- pio = ata_timing_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
-
- if (xfer_pio > 4)
- xfer_pio = 0;
-
- if (drive->id->eide_pio_iordy > 0) {
- for (xfer_pio = 5;
- xfer_pio>0 &&
- drive->id->eide_pio_iordy>eide_pio_timing[xfer_pio];
- xfer_pio--);
- } else {
- xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
- (drive->id->eide_pio_modes & 2) ? 0x04 :
- (drive->id->eide_pio_modes & 1) ? 0x03 :
- (drive->id->tPIO & 2) ? 0x02 :
- (drive->id->tPIO & 1) ? 0x01 : xfer_pio;
- }
-
- timing = (xfer_pio >= pio) ? xfer_pio : pio;
-
- switch(timing) {
- case 4: speed = XFER_PIO_4;break;
- case 3: speed = XFER_PIO_3;break;
- case 2: speed = XFER_PIO_2;break;
- case 1: speed = XFER_PIO_1;break;
- default:
- speed = (!drive->id->tPIO) ? XFER_PIO_0 : XFER_PIO_SLOW;
- break;
- }
- hpt3xx_tune_chipset(drive, speed);
-}
-
static void hpt3xx_tune_drive(struct ata_device *drive, u8 pio)
{
u8 speed;
@@ -866,8 +828,7 @@
on = 0;
verbose = 0;
no_dma_set:
-
- config_chipset_for_pio(drive);
+ hpt3xx_tune_chipset(drive, ata_best_pio_mode(drive));
}
udma_enable(drive, on, verbose);
diff -urN linux-2.5.21/drivers/ide/ide.c linux/drivers/ide/ide.c
--- linux-2.5.21/drivers/ide/ide.c 2002-06-13 20:29:39.000000000 +0200
+++ linux/drivers/ide/ide.c 2002-06-13 23:34:16.000000000 +0200
@@ -671,28 +671,12 @@
block = 1; /* redirect MBR access to EZ-Drive partn table */
ata_select(drive, 0);
- spin_unlock_irq(ch->lock);
if (ata_status_poll(drive, drive->ready_stat, BUSY_STAT | DRQ_STAT,
WAIT_READY, rq, &ret)) {
printk(KERN_WARNING "%s: drive not ready for command\n", drive->name);
- spin_lock_irq(ch->lock);
- return ret;
+ goto kill_rq;
}
- spin_lock_irq(ch->lock);
-
- /* This issues a special drive command.
- *
- * FIXME: move this down to idedisk_do_request().
- */
- if (rq->flags & REQ_SPECIAL)
- if (drive->type == ATA_DISK) {
- spin_unlock_irq(ch->lock);
- ret = ata_taskfile(drive, rq->special, NULL);
- spin_lock_irq(ch->lock);
-
- return ret;
- }
if (!ata_ops(drive)) {
printk(KERN_WARNING "%s: device type %d not supported\n",
@@ -704,8 +688,8 @@
* handler down to the device type driver.
*/
- if (ata_ops(drive)->XXX_do_request) {
- ret = ata_ops(drive)->XXX_do_request(drive, rq, block);
+ if (ata_ops(drive)->do_request) {
+ ret = ata_ops(drive)->do_request(drive, rq, block);
} else {
__ata_end_request(drive, rq, 0, 0);
ret = ide_stopped;
diff -urN linux-2.5.21/drivers/ide/ide-cd.c linux/drivers/ide/ide-cd.c
--- linux-2.5.21/drivers/ide/ide-cd.c 2002-06-13 20:29:39.000000000 +0200
+++ linux/drivers/ide/ide-cd.c 2002-06-13 23:39:32.000000000 +0200
@@ -732,46 +732,49 @@
struct ata_channel *ch = drive->channel;
ide_startstop_t startstop;
struct cdrom_info *info = drive->driver_data;
+ int ret;
+ spin_lock_irqsave(ch->lock, flags);
/* Wait for the controller to be idle. */
if (ata_status_poll(drive, 0, BUSY_STAT, WAIT_READY, rq, &startstop))
- return startstop;
-
- spin_lock_irqsave(ch->lock, flags);
-
- if (info->dma) {
- if (info->cmd == READ || info->cmd == WRITE)
- info->dma = !udma_init(drive, rq);
- else
- printk("ide-cd: DMA set, but not allowed\n");
- }
-
- /* Set up the controller registers. */
- OUT_BYTE(info->dma, IDE_FEATURE_REG);
- OUT_BYTE(0, IDE_NSECTOR_REG);
- OUT_BYTE(0, IDE_SECTOR_REG);
-
- OUT_BYTE(xferlen & 0xff, IDE_LCYL_REG);
- OUT_BYTE(xferlen >> 8 , IDE_HCYL_REG);
- ata_irq_enable(drive, 1);
- if (info->dma)
- udma_start(drive, rq);
-
- if (CDROM_CONFIG_FLAGS (drive)->drq_interrupt) {
- ata_set_handler(drive, handler, WAIT_CMD, cdrom_timer_expiry);
- OUT_BYTE (WIN_PACKETCMD, IDE_COMMAND_REG); /* packet command */
- spin_unlock_irqrestore(ch->lock, flags);
+ ret = startstop;
+ else {
+ if (info->dma) {
+ if (info->cmd == READ || info->cmd == WRITE)
+ info->dma = !udma_init(drive, rq);
+ else
+ printk("ide-cd: DMA set, but not allowed\n");
+ }
- return ide_started;
- } else {
- OUT_BYTE (WIN_PACKETCMD, IDE_COMMAND_REG); /* packet command */
- spin_unlock_irqrestore(ch->lock, flags);
+ /* Set up the controller registers. */
+ OUT_BYTE(info->dma, IDE_FEATURE_REG);
+ OUT_BYTE(0, IDE_NSECTOR_REG);
+ OUT_BYTE(0, IDE_SECTOR_REG);
+
+ OUT_BYTE(xferlen & 0xff, IDE_LCYL_REG);
+ OUT_BYTE(xferlen >> 8 , IDE_HCYL_REG);
+ ata_irq_enable(drive, 1);
+ if (info->dma)
+ udma_start(drive, rq);
+
+ if (CDROM_CONFIG_FLAGS (drive)->drq_interrupt) {
+ ata_set_handler(drive, handler, WAIT_CMD, cdrom_timer_expiry);
+ OUT_BYTE (WIN_PACKETCMD, IDE_COMMAND_REG); /* packet command */
+ ret = ide_started;
+ } else {
+ OUT_BYTE (WIN_PACKETCMD, IDE_COMMAND_REG); /* packet command */
- /* FIXME: Woah we have to ungrab the lock before the IRQ
- * handler gets called.
- */
- return handler(drive, rq);
+ /* FIXME: Oj kurwa! We have to ungrab the lock before
+ * the IRQ handler gets called.
+ */
+ spin_unlock_irqrestore(ch->lock, flags);
+ ret = handler(drive, rq);
+ spin_lock_irqsave(ch->lock, flags);
+ }
}
+ spin_unlock_irqrestore(ch->lock, flags);
+
+ return ret;
}
/*
@@ -797,10 +800,16 @@
if (cdrom_decode_status(&startstop, drive, rq, DRQ_STAT, &stat_dum))
return startstop;
} else {
+ /* FIXME: make this locking go away */
+ spin_lock_irqsave(ch->lock, flags);
/* Otherwise, we must wait for DRQ to get set. */
if (ata_status_poll(drive, DRQ_STAT, BUSY_STAT,
- WAIT_READY, rq, &startstop))
+ WAIT_READY, rq, &startstop)) {
+ spin_unlock_irqrestore(ch->lock, flags);
+
return startstop;
+ }
+ spin_unlock_irqrestore(ch->lock, flags);
}
/* Arm the interrupt handler and send the command to the device. */
@@ -1687,8 +1696,6 @@
return ret;
} else if (rq->flags & REQ_SPECIAL) {
- /* FIXME: make this unlocking go away*/
- spin_unlock_irq(ch->lock);
/*
* FIXME: Kill REQ_SEPCIAL and replace it with commands queued
* at the request queue instead as suggested by Linus.
@@ -1696,6 +1703,8 @@
* right now this can only be a reset...
*/
+ /* FIXME: make this unlocking go away*/
+ spin_unlock_irq(ch->lock);
cdrom_end_request(drive, rq, 1);
spin_lock_irq(ch->lock);
@@ -1704,8 +1713,6 @@
struct packet_command pc;
ide_startstop_t startstop;
- /* FIXME: make this unlocking go away*/
- spin_unlock_irq(ch->lock);
memset(&pc, 0, sizeof(pc));
pc.quiet = 1;
pc.timeout = 60 * HZ;
@@ -1713,10 +1720,13 @@
/* FIXME --mdcki */
rq->special = (char *) &pc;
+ /* FIXME: make this unlocking go away*/
+ spin_unlock_irq(ch->lock);
startstop = cdrom_do_packet_command(drive, rq);
+ spin_lock_irq(ch->lock);
+
if (pc.stat)
++rq->errors;
- spin_lock_irq(ch->lock);
return startstop;
}
@@ -2990,7 +3000,7 @@
attach: ide_cdrom_attach,
cleanup: ide_cdrom_cleanup,
standby: NULL,
- XXX_do_request: ide_cdrom_do_request,
+ do_request: ide_cdrom_do_request,
end_request: NULL,
ioctl: ide_cdrom_ioctl,
open: ide_cdrom_open,
diff -urN linux-2.5.21/drivers/ide/ide-disk.c linux/drivers/ide/ide-disk.c
--- linux-2.5.21/drivers/ide/ide-disk.c 2002-06-13 20:29:39.000000000 +0200
+++ linux/drivers/ide/ide-disk.c 2002-06-13 23:42:53.000000000 +0200
@@ -456,7 +456,7 @@
rq->special = &args;
- return ata_taskfile(drive, &args, rq);
+ return ata_do_taskfile(drive, &args, rq);
}
static ide_startstop_t lba28_do_request(struct ata_device *drive, struct request *rq, sector_t block)
@@ -496,7 +496,7 @@
rq->special = &args;
- return ata_taskfile(drive, &args, rq);
+ return ata_do_taskfile(drive, &args, rq);
}
/*
@@ -548,7 +548,7 @@
rq->special = &args;
- return ata_taskfile(drive, &args, rq);
+ return ata_do_taskfile(drive, &args, rq);
}
/*
@@ -560,14 +560,16 @@
*/
static ide_startstop_t idedisk_do_request(struct ata_device *drive, struct request *rq, sector_t block)
{
- unsigned long flags;
- struct ata_channel *ch = drive->channel;
- int ret;
+ /* This issues a special drive command.
+ */
+ if (rq->flags & REQ_SPECIAL)
+ return ata_do_taskfile(drive, rq->special, rq);
/* FIXME: this check doesn't make sense */
if (!(rq->flags & REQ_CMD)) {
blk_dump_rq_flags(rq, "idedisk_do_request - bad command");
__ata_end_request(drive, rq, 0, 0);
+
return ide_stopped;
}
@@ -590,6 +592,7 @@
if (st) {
BUG_ON(!ata_pending_commands(drive));
+
return ide_started;
}
}
@@ -1405,7 +1408,7 @@
attach: idedisk_attach,
cleanup: idedisk_cleanup,
standby: idedisk_standby,
- XXX_do_request: idedisk_do_request,
+ do_request: idedisk_do_request,
end_request: NULL,
ioctl: idedisk_ioctl,
open: idedisk_open,
diff -urN linux-2.5.21/drivers/ide/ide-floppy.c linux/drivers/ide/ide-floppy.c
--- linux-2.5.21/drivers/ide/ide-floppy.c 2002-06-13 20:29:39.000000000 +0200
+++ linux/drivers/ide/ide-floppy.c 2002-06-13 23:22:32.000000000 +0200
@@ -958,27 +958,25 @@
idefloppy_ireason_reg_t ireason;
int ret;
+ /* FIXME: Move this lock upwards.
+ */
+ spin_lock_irqsave(ch->lock, flags);
if (ata_status_poll(drive, DRQ_STAT, BUSY_STAT,
WAIT_READY, rq, &startstop)) {
printk (KERN_ERR "ide-floppy: Strange, packet command initiated yet DRQ isn't asserted\n");
- return startstop;
- }
-
- /* FIXME: this locking should encompass the above register
- * file access too.
- */
-
- spin_lock_irqsave(ch->lock, flags);
- ireason.all=IN_BYTE (IDE_IREASON_REG);
-
- if (!ireason.b.cod || ireason.b.io) {
- printk (KERN_ERR "ide-floppy: (IO,CoD) != (0,1) while issuing a packet command\n");
- ret = ide_stopped;
+ ret = startstop;
} else {
- ata_set_handler (drive, idefloppy_pc_intr, IDEFLOPPY_WAIT_CMD, NULL); /* Set the interrupt routine */
- atapi_write(drive, floppy->pc->c, 12); /* Send the actual packet */
- ret = ide_started;
+ ireason.all=IN_BYTE (IDE_IREASON_REG);
+
+ if (!ireason.b.cod || ireason.b.io) {
+ printk (KERN_ERR "ide-floppy: (IO,CoD) != (0,1) while issuing a packet command\n");
+ ret = ide_stopped;
+ } else {
+ ata_set_handler (drive, idefloppy_pc_intr, IDEFLOPPY_WAIT_CMD, NULL); /* Set the interrupt routine */
+ atapi_write(drive, floppy->pc->c, 12); /* Send the actual packet */
+ ret = ide_started;
+ }
}
spin_unlock_irqrestore(ch->lock, flags);
@@ -2047,7 +2045,7 @@
attach: idefloppy_attach,
cleanup: idefloppy_cleanup,
standby: NULL,
- XXX_do_request: idefloppy_do_request,
+ do_request: idefloppy_do_request,
end_request: idefloppy_end_request,
ioctl: idefloppy_ioctl,
open: idefloppy_open,
diff -urN linux-2.5.21/drivers/ide/ide-tape.c linux/drivers/ide/ide-tape.c
--- linux-2.5.21/drivers/ide/ide-tape.c 2002-06-13 20:29:39.000000000 +0200
+++ linux/drivers/ide/ide-tape.c 2002-06-13 23:21:33.000000000 +0200
@@ -2067,6 +2067,7 @@
tape->dsc_polling_frequency = IDETAPE_DSC_MA_FAST;
tape->dsc_timeout = jiffies + IDETAPE_DSC_MA_TIMEOUT;
idetape_postpone_request(drive, rq); /* Allow ide.c to handle other requests */
+
return ide_stopped;
}
if (tape->failed_pc == pc)
@@ -2074,20 +2075,22 @@
pc->callback(drive, rq); /* Command finished - Call the callback function */
return ide_stopped;
}
+ /* FIXME: this locking should encompass the above register
+ * file access too.
+ */
+
+ spin_lock_irqsave(ch->lock, flags);
#ifdef CONFIG_BLK_DEV_IDEDMA
if (test_and_clear_bit (PC_DMA_IN_PROGRESS, &pc->flags)) {
printk (KERN_ERR "ide-tape: The tape wants to issue more interrupts in DMA mode\n");
printk (KERN_ERR "ide-tape: DMA disabled, reverting to PIO\n");
udma_enable(drive, 0, 1);
+ spin_unlock_irqrestore(ch->lock, flags);
return ide_stopped;
}
#endif
- /* FIXME: this locking should encompass the above register
- * file access too.
- */
- spin_lock_irqsave(ch->lock, flags);
bcount.b.high = IN_BYTE (IDE_BCOUNTH_REG); /* Get the number of bytes to transfer */
bcount.b.low = IN_BYTE (IDE_BCOUNTL_REG); /* on this interrupt */
ireason.all = IN_BYTE (IDE_IREASON_REG);
@@ -2198,37 +2201,35 @@
ide_startstop_t startstop;
int ret;
+ /* FIXME: Move this lock upwards.
+ */
+ spin_lock_irqsave(ch->lock, flags);
if (ata_status_poll(drive, DRQ_STAT, BUSY_STAT,
WAIT_READY, rq, &startstop)) {
printk (KERN_ERR "ide-tape: Strange, packet command initiated yet DRQ isn't asserted\n");
- return startstop;
- }
-
- /* FIXME: this locking should encompass the above register
- * file access too.
- */
-
- spin_lock_irqsave(ch->lock, flags);
- ireason.all = IN_BYTE (IDE_IREASON_REG);
- while (retries-- && (!ireason.b.cod || ireason.b.io)) {
- printk(KERN_ERR "ide-tape: (IO,CoD != (0,1) while issuing a packet command, retrying\n");
- udelay(100);
- ireason.all = IN_BYTE(IDE_IREASON_REG);
- if (retries == 0) {
- printk(KERN_ERR "ide-tape: (IO,CoD != (0,1) while issuing a packet command, ignoring\n");
- ireason.b.cod = 1;
- ireason.b.io = 0;
- }
- }
- if (!ireason.b.cod || ireason.b.io) {
- printk (KERN_ERR "ide-tape: (IO,CoD) != (0,1) while issuing a packet command\n");
- ret = ide_stopped;
+ ret = startstop;
} else {
- tape->cmd_start_time = jiffies;
- ata_set_handler(drive, idetape_pc_intr, IDETAPE_WAIT_CMD, NULL); /* Set the interrupt routine */
- atapi_write(drive,pc->c,12); /* Send the actual packet */
- ret = ide_started;
+ ireason.all = IN_BYTE (IDE_IREASON_REG);
+ while (retries-- && (!ireason.b.cod || ireason.b.io)) {
+ printk(KERN_ERR "ide-tape: (IO,CoD != (0,1) while issuing a packet command, retrying\n");
+ udelay(100);
+ ireason.all = IN_BYTE(IDE_IREASON_REG);
+ if (retries == 0) {
+ printk(KERN_ERR "ide-tape: (IO,CoD != (0,1) while issuing a packet command, ignoring\n");
+ ireason.b.cod = 1;
+ ireason.b.io = 0;
+ }
+ }
+ if (!ireason.b.cod || ireason.b.io) {
+ printk (KERN_ERR "ide-tape: (IO,CoD) != (0,1) while issuing a packet command\n");
+ ret = ide_stopped;
+ } else {
+ tape->cmd_start_time = jiffies;
+ ata_set_handler(drive, idetape_pc_intr, IDETAPE_WAIT_CMD, NULL); /* Set the interrupt routine */
+ atapi_write(drive,pc->c,12); /* Send the actual packet */
+ ret = ide_started;
+ }
}
spin_unlock_irqrestore(ch->lock, flags);
@@ -2736,10 +2737,8 @@
}
} else if (jiffies - tape->dsc_polling_start > IDETAPE_DSC_MA_THRESHOLD)
tape->dsc_polling_frequency = IDETAPE_DSC_MA_SLOW;
- /* FIXME: make this unlocking go away*/
- spin_unlock_irq(ch->lock);
idetape_postpone_request(drive, rq);
- spin_lock_irq(ch->lock);
+
return ide_stopped;
}
switch (rq->flags) {
@@ -6128,7 +6127,7 @@
attach: idetape_attach,
cleanup: idetape_cleanup,
standby: NULL,
- XXX_do_request: idetape_do_request,
+ do_request: idetape_do_request,
end_request: idetape_end_request,
ioctl: idetape_blkdev_ioctl,
open: idetape_blkdev_open,
diff -urN linux-2.5.21/drivers/ide/ide-taskfile.c linux/drivers/ide/ide-taskfile.c
--- linux-2.5.21/drivers/ide/ide-taskfile.c 2002-06-13 20:15:09.000000000 +0200
+++ linux/drivers/ide/ide-taskfile.c 2002-06-13 23:41:56.000000000 +0200
@@ -177,9 +177,9 @@
}
/*
- * FIXME: Channel lock should be held on entry.
+ * Channel lock should be held on entry.
*/
-ide_startstop_t ata_taskfile(struct ata_device *drive,
+ide_startstop_t ata_do_taskfile(struct ata_device *drive,
struct ata_taskfile *ar, struct request *rq)
{
struct hd_driveid *id = drive->id;
@@ -196,27 +196,21 @@
if ((id->command_set_2 & 0x0400) && (id->cfs_enable_2 & 0x0400) &&
(drive->addressing == 1))
ata_out_regfile(drive, &ar->hobfile);
+
ata_out_regfile(drive, &ar->taskfile);
OUT_BYTE((ar->taskfile.device_head & (drive->addressing ? 0xE0 : 0xEF)) | drive->select.all,
IDE_SELECT_REG);
if (ar->handler) {
- unsigned long flags;
struct ata_channel *ch = drive->channel;
/* This is apparently supposed to reset the wait timeout for
* the interrupt to accur.
*/
- /* FIXME: this locking should encompass the above register
- * file access too.
- */
-
- spin_lock_irqsave(ch->lock, flags);
ata_set_handler(drive, ar->handler, WAIT_CMD, NULL);
OUT_BYTE(ar->cmd, IDE_COMMAND_REG);
- spin_unlock_irqrestore(ch->lock, flags);
/* FIXME: Warning check for race between handler and prehandler
* for writing first block of data. however since we are well
@@ -240,6 +234,7 @@
WAIT_DRQ, rq, &startstop)) {
printk(KERN_ERR "%s: no DRQ after issuing %s\n",
drive->name, drive->mult_count ? "MULTWRITE" : "WRITE");
+
return startstop;
}
@@ -261,6 +256,7 @@
return ide_started;
} else {
int i;
+ int ret;
/* Polling wait until the drive is ready.
*
@@ -278,7 +274,12 @@
if (!drive_is_ready(drive)) {
printk(KERN_ERR "DISASTER WAITING TO HAPPEN!\n");
}
- return ar->handler(drive, rq);
+ /* FIXME: make this unlocking go away*/
+ spin_unlock_irq(ch->lock);
+ ret = ar->handler(drive, rq);
+ spin_lock_irq(ch->lock);
+
+ return ret;
}
}
} else {
@@ -448,6 +449,6 @@
EXPORT_SYMBOL(ide_do_drive_cmd);
EXPORT_SYMBOL(ata_read);
EXPORT_SYMBOL(ata_write);
-EXPORT_SYMBOL(ata_taskfile);
+EXPORT_SYMBOL(ata_do_taskfile);
EXPORT_SYMBOL(ata_special_intr);
EXPORT_SYMBOL(ide_raw_taskfile);
diff -urN linux-2.5.21/drivers/ide/pdc202xx.c linux/drivers/ide/pdc202xx.c
--- linux-2.5.21/drivers/ide/pdc202xx.c 2002-06-13 20:29:39.000000000 +0200
+++ linux/drivers/ide/pdc202xx.c 2002-06-13 22:53:06.000000000 +0200
@@ -364,12 +364,12 @@
* 180, 120, 90, 90, 90, 60, 30
* 11, 5, 4, 3, 2, 1, 0
*/
-static void config_chipset_for_pio(struct ata_device *drive, byte pio)
+static void pdc202xx_tune_drive(struct ata_device *drive, u8 pio)
{
- byte speed;
+ u8 speed;
if (pio == 255)
- speed = ata_timing_mode(drive, XFER_PIO | XFER_EPIO);
+ speed = ata_best_pio_mode(drive);
else speed = XFER_PIO_0 + min_t(byte, pio, 4);
pdc202xx_tune_chipset(drive, speed);
@@ -543,7 +543,7 @@
} else goto no_dma_set;
} else if ((id->capability & 8) || (id->field_valid & 2)) {
no_dma_set:
- config_chipset_for_pio(drive, 5);
+ pdc202xx_tune_drive(drive, 255);
}
udma_enable(drive, on, verbose);
@@ -723,7 +723,7 @@
static void __init ide_init_pdc202xx(struct ata_channel *hwif)
{
- hwif->tuneproc = &config_chipset_for_pio;
+ hwif->tuneproc = &pdc202xx_tune_drive;
hwif->quirkproc = &check_in_drive_lists;
switch(hwif->pci_dev->device) {
diff -urN linux-2.5.21/drivers/ide/pdc4030.c linux/drivers/ide/pdc4030.c
--- linux-2.5.21/drivers/ide/pdc4030.c 2002-06-10 23:47:13.000000000 +0200
+++ linux/drivers/ide/pdc4030.c 2002-06-13 21:54:55.000000000 +0200
@@ -247,12 +247,19 @@
if (pdc4030_cmd(drive, PROMISE_GET_CONFIG)) {
return 0;
}
+
+ /* FIXME: Make this go away. */
+ spin_lock_irq(hwif->lock);
if (ata_status_poll(drive, DATA_READY, BAD_W_STAT,
WAIT_DRQ, NULL, &startstop)) {
printk(KERN_INFO
"%s: Failed Promise read config!\n",hwif->name);
+ spin_unlock_irq(hwif->lock);
+
return 0;
}
+ spin_unlock_irq(hwif->lock);
+
promise_read(drive, &ident, SECTOR_WORDS);
if (ident.id[1] != 'P' || ident.id[0] != 'T') {
return 0;
@@ -720,21 +727,34 @@
case WRITE: {
ide_startstop_t startstop;
-/*
- * Strategy on write is:
- * look for the DRQ that should have been immediately asserted
- * copy the request into the hwgroup's scratchpad
- * call the promise_write function to deal with writing the data out
- * NOTE: No interrupts are generated on writes. Write completion must be polled
- */
+ unsigned long flags;
+ struct ata_channel *ch = drive->channel;
+
+ /*
+ * Strategy on write is: look for the DRQ that should have been
+ * immediately asserted copy the request into the hwgroup's
+ * scratchpad call the promise_write function to deal with
+ * writing the data out.
+ *
+ * NOTE: No interrupts are generated on writes. Write
+ * completion must be polled
+ */
+
+ /* FIXME: Move this lock upwards.
+ */
+ spin_lock_irqsave(ch->lock, flags);
if (ata_status_poll(drive, DATA_READY, drive->bad_wstat,
WAIT_DRQ, rq, &startstop )) {
printk(KERN_ERR "%s: no DRQ after issuing "
"PROMISE_WRITE\n", drive->name);
+ spin_unlock_irqrestore(ch->lock, flags);
+
return startstop;
}
if (!drive->channel->unmask)
__cli(); /* local CPU only */
+ spin_unlock_irqrestore(ch->lock, flags);
+
return promise_do_write(drive, rq);
}
diff -urN linux-2.5.21/drivers/ide/serverworks.c linux/drivers/ide/serverworks.c
--- linux-2.5.21/drivers/ide/serverworks.c 2002-06-09 17:44:23.000000000 +0200
+++ linux/drivers/ide/serverworks.c 2002-06-13 22:53:06.000000000 +0200
@@ -226,44 +226,6 @@
return ide_config_drive_speed(drive, speed);
}
-static void config_chipset_for_pio(struct ata_device *drive)
-{
- unsigned short eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
- unsigned short xfer_pio = drive->id->eide_pio_modes;
- byte timing, speed, pio;
-
- pio = ata_timing_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
-
- if (xfer_pio > 4)
- xfer_pio = 0;
-
- if (drive->id->eide_pio_iordy > 0)
- for (xfer_pio = 5;
- xfer_pio>0 &&
- drive->id->eide_pio_iordy>eide_pio_timing[xfer_pio];
- xfer_pio--);
- else
- xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
- (drive->id->eide_pio_modes & 2) ? 0x04 :
- (drive->id->eide_pio_modes & 1) ? 0x03 :
- (drive->id->tPIO & 2) ? 0x02 :
- (drive->id->tPIO & 1) ? 0x01 : xfer_pio;
-
- timing = (xfer_pio >= pio) ? xfer_pio : pio;
-
- switch(timing) {
- case 4: speed = XFER_PIO_4;break;
- case 3: speed = XFER_PIO_3;break;
- case 2: speed = XFER_PIO_2;break;
- case 1: speed = XFER_PIO_1;break;
- default:
- speed = (!drive->id->tPIO) ? XFER_PIO_0 : XFER_PIO_SLOW;
- break;
- }
- (void) svwks_tune_chipset(drive, speed);
- drive->current_speed = speed;
-}
-
static void svwks_tune_drive(struct ata_device *drive, byte pio)
{
byte speed;
@@ -337,7 +299,7 @@
on = 0;
verbose = 0;
no_dma_set:
- config_chipset_for_pio(drive);
+ svwks_tune_chipset(drive, ata_best_pio_mode(drive));
}
udma_enable(drive, on, verbose);
diff -urN linux-2.5.21/drivers/ide/sis5513.c linux/drivers/ide/sis5513.c
--- linux-2.5.21/drivers/ide/sis5513.c 2002-06-09 07:29:00.000000000 +0200
+++ linux/drivers/ide/sis5513.c 2002-06-13 22:53:06.000000000 +0200
@@ -263,15 +263,11 @@
/* Set per-drive active and recovery time */
-static void config_art_rwp_pio(struct ata_device *drive, u8 pio)
+static int config_art_rwp_pio(struct ata_device *drive, u8 pio)
{
struct ata_channel *hwif = drive->channel;
- struct pci_dev *dev = hwif->pci_dev;
-
- byte timing, drive_pci, test1, test2;
-
- unsigned short eide_pio_timing[6] = {600, 390, 240, 180, 120, 90};
- unsigned short xfer_pio = drive->id->eide_pio_modes;
+ struct pci_dev *dev = hwif->pci_dev;
+ u8 drive_pci, test1, test2, speed;
#ifdef DEBUG
sis5513_load_verify_registers(dev, "config_drive_art_rwp_pio start");
@@ -279,25 +275,6 @@
config_drive_art_rwp(drive);
- if (pio == 255)
- pio = ata_timing_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
-
- if (xfer_pio> 4)
- xfer_pio = 0;
-
- if (drive->id->eide_pio_iordy > 0) {
- for (xfer_pio = 5;
- (xfer_pio > 0) &&
- (drive->id->eide_pio_iordy > eide_pio_timing[xfer_pio]);
- xfer_pio--);
- } else {
- xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
- (drive->id->eide_pio_modes & 2) ? 0x04 :
- (drive->id->eide_pio_modes & 1) ? 0x03 : xfer_pio;
- }
-
- timing = (xfer_pio >= pio) ? xfer_pio : pio;
-
#ifdef DEBUG
printk("SIS5513: config_drive_art_rwp_pio, drive %d, pio %d, timing %d\n",
drive->dn, pio, timing);
@@ -308,7 +285,7 @@
case 1: drive_pci = 0x42; break;
case 2: drive_pci = 0x44; break;
case 3: drive_pci = 0x46; break;
- default: return;
+ default: return 1;
}
/* register layout changed with newer ATA100 chips */
@@ -320,7 +297,7 @@
test1 &= ~0x0F;
test2 &= ~0x07;
- switch(timing) {
+ switch(pio) {
case 4: test1 |= 0x01; test2 |= 0x03; break;
case 3: test1 |= 0x03; test2 |= 0x03; break;
case 2: test1 |= 0x04; test2 |= 0x04; break;
@@ -330,7 +307,7 @@
pci_write_config_byte(dev, drive_pci, test1);
pci_write_config_byte(dev, drive_pci+1, test2);
} else {
- switch(timing) { /* active recovery
+ switch(pio) { /* active recovery
v v */
case 4: test1 = 0x30|0x01; break;
case 3: test1 = 0x30|0x03; break;
@@ -344,21 +321,7 @@
#ifdef DEBUG
sis5513_load_verify_registers(dev, "config_drive_art_rwp_pio start");
#endif
-}
-
-static int config_chipset_for_pio(struct ata_device *drive, u8 pio)
-{
- u8 speed;
-
- switch(pio) {
- case 4: speed = XFER_PIO_4; break;
- case 3: speed = XFER_PIO_3; break;
- case 2: speed = XFER_PIO_2; break;
- case 1: speed = XFER_PIO_1; break;
- default: speed = XFER_PIO_0; break;
- }
-
- config_art_rwp_pio(drive, pio);
+ speed = XFER_PIO_0 + min_t(u8, pio, 4);
drive->current_speed = speed;
return ide_config_drive_speed(drive, speed);
}
@@ -424,12 +387,14 @@
case XFER_SW_DMA_0:
break;
#endif /* CONFIG_BLK_DEV_IDEDMA */
- case XFER_PIO_4: return((int) config_chipset_for_pio(drive, 4));
- case XFER_PIO_3: return((int) config_chipset_for_pio(drive, 3));
- case XFER_PIO_2: return((int) config_chipset_for_pio(drive, 2));
- case XFER_PIO_1: return((int) config_chipset_for_pio(drive, 1));
+ case XFER_PIO_4:
+ case XFER_PIO_3:
+ case XFER_PIO_2:
+ case XFER_PIO_1:
case XFER_PIO_0:
- default: return((int) config_chipset_for_pio(drive, 0));
+ return config_art_rwp_pio(drive, speed - XFER_PIO_0);
+ default:
+ return config_art_rwp_pio(drive, 0);
}
drive->current_speed = speed;
#ifdef DEBUG
@@ -440,7 +405,10 @@
static void sis5513_tune_drive(struct ata_device *drive, u8 pio)
{
- (void) config_chipset_for_pio(drive, pio);
+ if (pio == 255)
+ pio = ata_best_pio_mode(drive) - XFER_PIO_0;
+
+ (void)config_art_rwp_pio(drive, min_t(u8, pio, 4));
}
#ifdef CONFIG_BLK_DEV_IDEDMA
@@ -473,8 +441,7 @@
int verbose = 1;
config_drive_art_rwp(drive);
- config_art_rwp_pio(drive, 5);
- config_chipset_for_pio(drive, 5);
+ sis5513_tune_drive(drive, 255);
if (id && (id->capability & 1) && drive->channel->autodma) {
/* Consult the list of known "bad" drives */
@@ -515,7 +482,7 @@
on = 0;
verbose = 0;
no_dma_set:
- (void) config_chipset_for_pio(drive, 5);
+ sis5513_tune_drive(drive, 255);
}
udma_enable(drive, on, verbose);
diff -urN linux-2.5.21/drivers/scsi/ide-scsi.c linux/drivers/scsi/ide-scsi.c
--- linux-2.5.21/drivers/scsi/ide-scsi.c 2002-06-13 20:29:39.000000000 +0200
+++ linux/drivers/scsi/ide-scsi.c 2002-06-13 23:23:25.000000000 +0200
@@ -403,25 +403,24 @@
ide_startstop_t startstop;
int ret;
+ /* FIXME: Move this lock upwards.
+ */
+ spin_lock_irqsave(ch->lock, flags);
if (ata_status_poll(drive, DRQ_STAT, BUSY_STAT,
WAIT_READY, rq, &startstop)) {
printk (KERN_ERR "ide-scsi: Strange, packet command initiated yet DRQ isn't asserted\n");
- return startstop;
- }
-
- /* FIXME: this locking should encompass the above register
- * file access too.
- */
- spin_lock_irqsave(ch->lock, flags);
- ireason = IN_BYTE(IDE_IREASON_REG);
-
- if ((ireason & (IDESCSI_IREASON_IO | IDESCSI_IREASON_COD)) != IDESCSI_IREASON_COD) {
- printk (KERN_ERR "ide-scsi: (IO,CoD) != (0,1) while issuing a packet command\n");
- ret = ide_stopped;
+ ret = startstop;
} else {
- ata_set_handler(drive, idescsi_pc_intr, get_timeout(pc), NULL);
- atapi_write(drive, scsi->pc->c, 12);
- ret = ide_started;
+ ireason = IN_BYTE(IDE_IREASON_REG);
+
+ if ((ireason & (IDESCSI_IREASON_IO | IDESCSI_IREASON_COD)) != IDESCSI_IREASON_COD) {
+ printk (KERN_ERR "ide-scsi: (IO,CoD) != (0,1) while issuing a packet command\n");
+ ret = ide_stopped;
+ } else {
+ ata_set_handler(drive, idescsi_pc_intr, get_timeout(pc), NULL);
+ atapi_write(drive, scsi->pc->c, 12);
+ ret = ide_started;
+ }
}
spin_unlock_irqrestore(ch->lock, flags);
@@ -549,7 +548,7 @@
owner: THIS_MODULE,
attach: idescsi_attach,
cleanup: idescsi_cleanup,
- XXX_do_request: idescsi_do_request,
+ do_request: idescsi_do_request,
end_request: idescsi_end_request,
open: idescsi_open,
release: idescsi_release,
diff -urN linux-2.5.21/include/linux/ide.h linux/include/linux/ide.h
--- linux-2.5.21/include/linux/ide.h 2002-06-13 20:29:39.000000000 +0200
+++ linux/include/linux/ide.h 2002-06-13 23:29:55.000000000 +0200
@@ -545,7 +545,7 @@
void (*attach) (struct ata_device *);
int (*cleanup)(struct ata_device *);
int (*standby)(struct ata_device *);
- ide_startstop_t (*XXX_do_request)(struct ata_device *, struct request *, sector_t);
+ ide_startstop_t (*do_request)(struct ata_device *, struct request *, sector_t);
int (*end_request)(struct ata_device *, struct request *, int);
int (*ioctl)(struct ata_device *, struct inode *, struct file *, unsigned int, unsigned long);
@@ -657,7 +657,7 @@
extern void ata_read(struct ata_device *, void *, unsigned int);
extern void ata_write(struct ata_device *, void *, unsigned int);
-extern ide_startstop_t ata_taskfile(struct ata_device *,
+extern ide_startstop_t ata_do_taskfile(struct ata_device *,
struct ata_taskfile *, struct request *);
/*
