| From: |
| Alok Kataria <akataria@vmware.com> |
| To: |
| Ingo Molnar <mingo@elte.hu>, Thomas Gleixner <tglx@linutronix.de> |
| Subject: |
| [PATCH] x86: Reduce the default HZ value |
| Date: |
| Mon, 04 May 2009 11:44:21 -0700 |
| Message-ID: |
| <1241462661.412.8.camel@alok-dev1> |
| Cc: |
| the arch/x86 maintainers <x86@kernel.org>,
LKML <linux-kernel@vger.kernel.org>, alan@lxorguk.ukuu.org.uk |
| Archive‑link: | |
Article |
Hi,
Given that there were no major objections that came up regarding
reducing the HZ value in http://lkml.org/lkml/2009/4/27/499.
Below is the patch which actually reduces it, please consider for tip.
Thanks,
Alok
--
With HRT support in the kernel we shouldn't actually be needing a high interrupt
frequency. This patch reduces the HZ value to 100 for x86 defconfig.
A high HZ value may affect the performance of the system if its nonidle.
I ran a simple experiment with 2.6.29 kernel running on VMware..
A simple tight loop took about 264s to complete with a HZ value of 1000.
The system serviced a total of 264405 timer interrupts during that time.
The same loop with HZ=100 took only about 255sec to complete.
Total timer interrupts were 25593.
More information here - http://lkml.org/lkml/2009/4/28/401
With highres timers most of the important timers are not tied down with the
how often the jiffy value is updated so this shouldn't have any adverse
effects on the latency of these timers either.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Index: linux-tip-master/arch/x86/configs/i386_defconfig
===================================================================
--- linux-tip-master.orig/arch/x86/configs/i386_defconfig 2009-05-01 16:47:43.000000000 -0700
+++ linux-tip-master/arch/x86/configs/i386_defconfig 2009-05-01 16:49:48.000000000 -0700
@@ -312,11 +312,11 @@
CONFIG_X86_PAT=y
CONFIG_EFI=y
CONFIG_SECCOMP=y
-# CONFIG_HZ_100 is not set
+CONFIG_HZ_100=y
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
-CONFIG_HZ_1000=y
-CONFIG_HZ=1000
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=100
CONFIG_SCHED_HRTICK=y
CONFIG_KEXEC=y
CONFIG_CRASH_DUMP=y
Index: linux-tip-master/arch/x86/configs/x86_64_defconfig
===================================================================
--- linux-tip-master.orig/arch/x86/configs/x86_64_defconfig 2009-05-01 16:37:53.000000000 -0700
+++ linux-tip-master/arch/x86/configs/x86_64_defconfig 2009-05-01 16:50:22.000000000 -0700
@@ -316,11 +316,11 @@
CONFIG_X86_PAT=y
CONFIG_EFI=y
CONFIG_SECCOMP=y
-# CONFIG_HZ_100 is not set
+CONFIG_HZ_100=y
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
-CONFIG_HZ_1000=y
-CONFIG_HZ=1000
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=100
CONFIG_SCHED_HRTICK=y
CONFIG_KEXEC=y
CONFIG_CRASH_DUMP=y
